Plumbing Basics: Your Starting Point for When Installing a Bathtub
Plumbing Basics: Your Starting Point for When Installing a Bathtub
Blog Article
Listed here below yow will discover a bunch of high-quality information concerning Tools You Need to Install a New Bathtub .
Mounting a bath tub isn't exactly rocket science, however it does require solid plumbing, woodworking, and also often, tiling abilities. Replacing an old tub with a new one is additionally a reasonably challenging task. If the old bathtub is easily accessible, the job can relocate easily; if you have to open up a wall surface to remove the old tub as well as position the brand-new tub, the task is a lot harder. In either situation, the task is within a home handyman's abilities, although you will certainly require a helper to leave the old bathtub as well as set in the brand-new one. Make certain you have actually certified on your own for the work and also fit attempting it. Instead of hiring a specialist to take over a halfway-completed task, it is much better to consider using one prior to you start. Chances are you might require a specialist plumber to make tube connections.
This short article will certainly help you mount a new bath tub in your washroom if you have actually already purchased a brand-new tub and do not need to transform the setup of your previous water system pipes.
Your devices and also product list should consist of the following:
Planning for the Installment
Firstly, the supporting frame supplied with the bath ought to be fitted (if required) according to the supplier's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the tap block, it is important to make certain that if the tap includes a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets unit to stop strain on the bath tub.
Fit the flexible faucet connectors to the bottom of the two taps utilizing 2 nuts and also olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom should now prepare to be fitted in its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water. After doing so, activate the taps to drain pipes any water staying in the system. The process of getting rid of the existing faucets can be rather bothersome due to the restricted accessibility that is typically the instance.
Utilize a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a towel all set for the continuing to be water that will come from the pipelines. When the supply pipes have been eliminated, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from turning during this process. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleansed of any kind of old securing compound.
Before going on to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bathtub
Utilizing the two wood boards under its feet, put the tub in the called for placement. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The following goal is to guarantee that the tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the tub till the spirit level checks out level.
To install taps, fit all-time low of the outermost versatile tap adapter to the appropriate supply pipeline by making a compression join; then do the exact same for the other tap.
Turn on the water and check all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill the tub as well as additionally inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Lastly, repair the bath paneling as described in the maker's user's manual. Tiling and securing around the bathtub should wait till the tub has actually been made use of at the very least when as this will certainly settle it right into its last placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will need a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin guaranteeing that the washers remain in area in between the faucet and the sink. Safeguard the tap in position with the manufacturer given backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind should be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bathroom fulfills the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split a rigid seal, creating the water to penetrate the wall between the bath and also the tiling, bring about problems with moisture as well as feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to allow for the activity experienced when the tub is in use. The sealant can break fairly early if you do not take into consideration this motion before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise easily offered on the marketplace. It is a good idea to fit the tiles using water-resistant or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm just very involved in How to Install a Bathtub and I am hoping you enjoyed reading my page. Sharing is good. You won't know, you will be doing someone a favor. Thanks for going through it.
Stress-free fix? Contact. Report this page